Carbon steel — called black or structural steel in the shop — is the material we cut and bend most often. The most popular grades are S235 and S355: both cut, bend and weld well, and differ mainly in strength. At ADJATECH, we stock them in thicknesses of 0.5–25 mm and cut them with a fiber laser — with oxygen when productivity matters, or with nitrogen when the edge must be free of oxides. Below, we explain the designations, the differences between the grades, and what to keep in mind when cutting, bending and protecting carbon steel.
What the S235JR and S355J2 designations mean
Non-alloy structural steels are described by the PN-EN 10025-2 standard. The designation consists of several parts:
- S — structural steel.
- 235, 355 — minimum yield strength in MPa (for thicknesses up to 16 mm).
- JR, J0, J2 — impact toughness: required impact energy of 27 J at +20 °C, 0 °C and −20 °C, respectively. The "lower" the test temperature, the better the steel withstands dynamic loads in cold conditions.
S235 vs. S355 — comparison
| Feature | S235 | S355 |
|---|---|---|
| Minimum yield strength (up to 16 mm) | 235 MPa | 355 MPa |
| Tensile strength (3–100 mm) | 360–510 MPa | 470–630 MPa |
| Weldability | very good | good; thick sections may require preheating |
| Bending | easy, smaller radii | greater force and larger radii, more springback |
| Typical applications | brackets, guards, frames, less heavily loaded components | load-bearing structures, machine components, parts where weight matters |
For the same load capacity, a part made of S355 can be thinner than one made of S235, which reduces weight and often cutting cost. If your design doesn't require higher strength, S235 is easier to process.
Laser cutting carbon steel: oxygen or nitrogen
Black steel is laser cut mainly with oxygen. Oxygen reacts with the heated metal and assists the process, so thick plates are cut efficiently. However, a thin layer of oxides remains on the edge. It doesn't interfere with welding structures, but it can weaken the adhesion of powder coating. If the part will be painted or the edge needs to be bright, thin and medium-thickness sheets are cut with nitrogen. Tell us in your inquiry what will happen to the part after cutting, and we'll select the gas.
Sheet surface condition matters
Hot-rolled sheets are covered with mill scale, and sheets stored for a long time with rust. Mill scale, rust, paint or oil reduce cutting stability and edge quality. Clean or pickled sheet cuts more evenly, so with customer-supplied material we always check its condition before production starts.
Special grades made to order
Besides S235 and S355, we cut to order, among others:
- Hardox 400 and 450 (2–20 mm): wear-resistant steel for plowshares, buckets, liners and parts exposed to abrasion. The narrow heat-affected zone of the laser limits the local drop in hardness at the edge.
- Galvanized steel Z275 — during cutting the zinc evaporates near the edge, so the edge itself loses its zinc protection; for exterior parts it is worth protecting it.
- Spring steel C75S, tool steel 1.2379 (high-alloy, not carbon) and boron steel 22MnB5 — for springs, flat tools and parts that undergo hardening.
Thickness ranges for these grades are given in the material table on the laser cutting page.
Corrosion protection
Unprotected carbon steel rusts, so finished parts are most often painted or coated. Powder coating is the most popular option. We describe how to choose protection for your operating conditions in the article on anti-corrosion coatings. Before painting, it is worth cleaning oxides off an edge cut with oxygen, or cutting with nitrogen from the start.
Frequently asked questions
Which grade should I choose if I have no requirements from calculations?
S235 is usually sufficient for covers, brackets and lightly loaded parts. When load capacity at the lowest possible weight matters, S355 is the better choice, but the final decision should be made by the design engineer.
Can you provide a material certificate?
Ask about it when requesting a quote. Requirements for material documents are best defined before we order the sheet.
Can carbon steel be bent and welded right after cutting?
Yes. An edge cut with a laser is suitable for bending and welding without additional processing. We describe the design rules for bent parts in the article on sheet metal bending.